-
東莞創億嘉潤滑油有限公司
電話:0769-81283290
聯系人:劉超
手機:13725804996
企業QQ:1352876343
郵箱:1352876343@qq.com
網址:m.gshyjc.cn
地址:廣東省東莞市南城區高新產業園區宏一路
郵編:523073
|
殼牌潤滑油系列 > 殼牌航空潤滑油 > AEROSHELL FLUID 31 |
AEROSHELL FLUID 31 詳細說明 (瀏覽1271次) |
AEROSHELL FLUID 31 AeroShell Fluid 31 is a synthetic hydrocarbon based aircraft hydraulic fluid with greatly improved fire resistance characteristics when compared with conventional petroleum products. AeroShell Fluid 31 has a specially designed base stock which imparts a relatively high flash point, excellent low temperature properties and good oxidation and thermal stability. In addition, AeroShell Fluid 31 is formulated with high technology additives to provide oxidation and corrosion resistance, antiwear, and anti-foaming protection. AeroShell Fluid 31 is superclean filtered to ensure optimum performance in particulate monitored systems. AeroShell Fluid 31 is dyed red. The useful operating temperature range is –40 to +205°C. APPLICATIONS AeroShell Fluid 31 is recommended for use in aircraft, ordnance, and missile systems operating from –40°C to +205°C . This fluid should be considered for use in auto pilots, shock absorbers, brakes, flight control systems, hydraulic servo-controlled systems and other systems using synthetic elastomer seals. An increasing number of aircraft manufacturers now recommend use of this type of fluid in aircraft hydraulic systems in preference to mineral hydraulic oils. This move has been prompted by need to use fluids with better fire resistant properties. AeroShell Fluid 31 is also approved for use in the Honeywell (formerly Garrett) cooling turbine (cabin air compressors). Increasingly this type of hydraulic fluid is being adopted for use in hydraulic systems of military aircraft in place of mineral hydraulic fluids. AeroShell Fluid 31 is a synthetic hydrocarbon oil and should not be used in contact with incompatible seal materials. Refer to the General Notes at the front of this section for further information. AeroShell Fluid 31 is compatible with AeroShell Fluids 4, 41, 51, 61 and 71 and can be used in systems designed to operate with MIL-PRF-5606, MIL-PRF-6083, MIL-PRF-87257 and MIL-PRF-46170 fluids. Chlorinated solvents should not be used for cleaning hydraulic components which use AeroShell Fluid 31. The residual solvent contaminates the hydraulic fluid and may lead to corrosion. www.shell.com/aviation 190 Hydraulic Fluids SPECIFICATIONS U.S. Approved MIL-PRF-83282D British (MIL-PRF-83282D) French Equivalent to DCSEA 437/A Russian – NATO Code H-537 Joint Service Designation OX-19 PROPERTIES MIL-PRF-83282D TYPICAL Oil type Synthetic Synthetic Hydrocarbon Hydrocarbon Kinematic viscosity mm 2 /s @ 205°C 1.0 min 1.07 @ 100°C 3.45 min 3.53 @ 40°C 14.0 min 14.33 @ –40°C 2200 max 2098 Flashpoint Cleveland Open Cup °C 205 min 237 Fire Point °C 245 min 251 Total Acidity mgKOH/g 0.10 max 0.01 Evaporation loss 6.5 hrs @150°C % m 20 max 10 Relative density @ 15.6/15.6°C Report 0.850 Pourpoint °C –55 max Below –55 Table continuedNOTES The AeroShell Book Edition 18 2003 193 Hydraulic Fluids www.shell.com/aviation 192 Hydraulic Fluids PROPERTIES MIL-PRF-83282D TYPICAL Low temperature stability 72 hrs @ ?40°C Must pass Passes High temperature stability 100 hrs @ 205°C Must pass Passes Gravimetric Filtration, mg/100ml 0.3 max 0.2 Filtration time minutes 15 max Less than 15 Particle Count, Automatic, per Lt 5 to 15 μm 10000 max 1331 16 to 25 μm 1000 max 190 26 to 50 μm 150 max 55 51 to 100 μm 20 max 4 >100 μm 5 max 0 Water content ppm 100 max 82 Foam resistance ASTM Seq 1 Must pass Passes Flame propagation cm/s Must pass Passes Rubber swell, NBR-L % 18 to 30 Passes 4-Ball Wear, 1 hr @ 75°C scar dia, mm 1 kg load/1200 rpm 0.21 max 0.18 10 kg load/1200 rpm 0.30 max 0.24 40 kg load/1200 rpm 0.65 max 0.50 Oxidation & corrosion stability 168 hrs @ 121°C – metal weight change Must pass Passes – viscosity change @ 40°C % 10 max Less than 10 – change in acidity mgKOH/g 0.2 max Less than 0.02 Flammability Must pass Passes A viscosity/temperature curve is shown at the end of this section. |
|
|